* RECALIBRATE THE OSCILLATORS AFTER DOING ANY OF THE ABOVE MODIFICATIONS

*********A**********
1. Check Mains voltage setting.
2. Plug in Card A only. /!\
3. PSU Switch on. Adjust
VR2 for +12 volts. // voltmetre
4. PSU Adjust
VR1 for -9 volts. // voltmetre
5. Plug in Cards B and C.
6. PSU Recheck +12V and -9V. // voltmetre
7. REVERB Adjust
VR3 so that mixing occurs above 2 on the Reverb Mix knob.
8. REVERB Check the voltage control of reverb mix.
9. O/P Adjust
VR4 and VR5 for zero residual signals. // osc signal in 1 et 2 / volumes à 0 // pas de son OK
10. O/P Check the tracking of Level knobs 4-5-6.

*********B**********
11. ENV Set Trapezoid speed to 65Hz with
VR12 // env 0 0 0 0 0 0 trapez out dans in 1 65Hz // voltmeter freq hz ou soft
12. ENV Set
VR13 clockwise. // osc dans env in, volume env 0
13. ENV Adjust
VR7 for minimum residual signal. // pas de son OK
14. ENV Adjust
VR13 until signal just reappears, then back off to zero. // pas de son OK
15. ENV Check that maximum On time is at least 4 seconds.
16. ENV Check that maximum Decay time is at least 15 seconds. // ON R148
17. ENV Check that recycling occurs with Off set at 5.
18. ENV Check that recycling does NOT occur with Off set abaove 7. // OFF R143
19. ENV Check that Trigger functions and does not jam.
20. FILT With filter in oscillation and Frequency control on 5, set
VR6 for 261Hz.
21. FILT Check that Response control gives filtering below 5 and oscillation above.
22. FILT Check the shape of the oscillating Sine wave.
23. RM Adjust
VR10 for fundamental rejection on A residual signal. osc 1 dans A in // pas de son OK
24. RM Adjust
VR9 for 1st harmonic rejection on A residual signal.
25. RM Adjust
VR11 for fundamental rejection on B residual signal. osc 2 dans B in // pas de son OK
26. RM Adjust
VR8 for 1st harmonic rejection on B residual signal.
27. RM Check for frequency doubling when both inputs are the same.
28. I/P Check both channels for correct gain on both Hi and Lo inputs.

*********C**********
29. OSC1 Adjust
VR17 for best sine wave shape. // oscillo
30. OSC1 With Frequency on 6 set
VR15 for 261Hz.
31. OSC1 With Frequency on 8 add R290 (sot) to achieve 2088Hz.
32. OSC1 Recheck last two steps.
33. OSC1 Check both waveforms.
35. OSC2 Set
VR20 half-way.
36. OSC2 Pad shape resistors R227/R228 to achieve correct shapes.
37. OSC2 With Frequency on 6 set
VR19 for 261Hz.
38. OSC2 With Frequency on 8 add R291 (sot) to achieve 2088Hz.
39. OSC2 Recheck last two steps.
40. OSC1/2 Adjust
VR20 to achieve oscillator tracking to 2kHz.
41. OSC3 Pad shape resistors R261/R262 to achieve correct shapes.
42. OSC3 With Frequency on 8 set
VR21 for 63Hz.
43. NOISE Select a (transistor) diode for good bandwidth and level. // il met du temps à arriver
44. NOISE Adjust
VR22 for around 3 volts p-p noise.
45. NOISE Check the operation of the noise colour control.
46. METER Set signal zero on the meter itself and check operation.
47. METER Adjust
VR14 for control voltage zero.
48. JOYSTICK Adjust vertical for equal excursions on meter.
49. JOYSTICK Adjust horizontal for equal excursions on meter.